Addigy® P1210

Selective Laser Sintering [SLS]

Loading contents...

Addigy® P1210

Selective Laser Sintering [SLS]

Material info

About Addigy® P1210

The first material from Covestro’s powder platform, this PBT powder offers customers a widely-known material in the industrial sector the only solution for small series production via additive manufacturing in industrial applications requiring electrical insulation such as automotive electronics.

Color & Finishes

White neutral

Standard

Technology

Selective Laser Sintering [SLS]

DSM-Material-Guide-0

Material Properties

Tensile Strength X

47 MPa

Tensile Strength Z

30 MPa

Heat Deflection Temp

165 MPa

Tensile Modulus X

2600 MPa

Tensile Modulus Z

2600 MPa

Elongation at Break X

220%

Elongation at Break Z

120%

Description

Applications

Connectors, automobile electronics, electrical, lighting

Properties

Excellent dielectric properties, recyclable, improved dimensional stability due to lower moisture uptake

Design Guidelines

Bounding Box

Bounding Box Max
190x190x290 mm

Bounding Box Min
X + Y + Z ≥ 15 mm

The bounding box is a 3D imaginary outline of a box that encloses the smallest area occupied by your model. Your model must be within the minimum and maximum bounding box sizes. If the size of the model is close to the maximum bounding box, then the printing orientation will be restricted.

Walls

Supported Wall Thickness Min

1.0mm

Unsupported Wall Thickness Min

1.0mm

A supported wall is connected at least on two sides of the wall, while an unsupported wall is connected only on one side of the wall. Walls that do not meet the minimum requirements may not survive printing and cleaning processes. Additionally, models may still be rejected based on the wall geometry of the model. Please consider the size of your model and reinforce the walls or add support structures as needed as minimum guidelines will not always be adequate for large models.

Wires

Supported Wires Min

1.2mm

Unsupported Wires Min

1.0mm

A wire is a circular, rectangular or even triangular feature that is thinner in its unconnected directions than its length. A supported wire is connected at least on two sides of the model, while an unsupported wire is connected on one side of the model. Wires that do not meet the minimum requirements may not survive printing and cleaning processes. Additionally, models may still be rejected based on the wire geometry of the model. Please consider the size of your model and reinforce the wires or add support structures as needed as minimum guidelines will not always be adequate for large models.

Details

Details Min Embossed

0.5mm high & wide / 0.5 mm high & wide

Details Min Engraved

0.8mm high & 0.8mm wide / 0.8mm high & 0.8mm wide

For text, the ratio between width and depth, should be 1:1 and sans-serif fonts are preferred for line weight consistency.

Escape Holes

Single Escape Hole Diameter (Min)

4.0mm

Multiple Escape Hole Diameter (Min)

2.0mm

Escape holes are necessary to empty the support material of a hollow model. Two escape holes at the opposite ends of the model is optimal for the support removal process. Please consider the size of your model and make the escape holes bigger or add more escape holes as needed as minimum guidelines will not always be adequate for large models.

A single escape hole at the end of a cavity will not allow material in the corners near the escape hole to fully escape. So we recommend multiple escape holes at both ends of the cavity.

Clearance

Min

0.5mm

Clearance is the space between two individual parts in a model. If the space among the individual parts do not meet the minimum clearance, then parts can fuse together or can be difficult to clean. This is important for movable pieces like hinges, gears, etc.

Sprues

2 mm thick, attached in at least 2 places per part

Sprues are wires that keep two or more parts together. Parts should be connected with a minimum of two sprues each. Please consider the size of your sprues and increase them as needed as minimum guidelines will not always be adequate for large models. If the sprues are within the guidelines and are broken, but there is no damage to your model, we will still ship them as is.

Interlocking & Enclosed Parts

Interlocking
Yes

Enclosed
Yes

Parts in File

Max
Up to 250 parts accepted

Accuracy

Accuracy 0.15 mm + 0.5%

For example: a product with dimensions of 50x50x100 mm can be 0.15 mm + 0.0015*100 mm = 0.3 mm bigger or smaller in any direction.

Other Materials

SLS, Polypropylene (PP)

Ultrasint® PP nat 01

Chemical resistanceHigh ductilityHigh elongation at break 30%

Application: Coolant reservoirs, custom production tools, electrical and sports goods, health care and orthopedic products

Photopolymer

Full Color Mimaki

Application: Figurine, medical models, architecture, terrain models, realistic visual prototypes