Photopolymer vat photopolymerization

High Temp ABS-like 6000

Stereolithography [SLA]

Loading contents...

Photopolymer vat photopolymerization

High Temp ABS-like 6000

Stereolithography [SLA]

Material info

About High Temp ABS-like 6000

ABS-like is our closest representation of Injection Molded ABS in a printed material

Color & Finishes

Ivory (Supports removed and lightly sanded)

Technology

Stereolithography [SLA]

Design Guidelines

Bounding Box

Bounding Box Max
490 × 390 × 200 mm

Bounding Box Min
X + Y + Z > 9 mm 1 x 1 x 1 mm

The bounding box is a 3D imaginary outline of a box that encloses the smallest area occupied by your model. Your model must be within the minimum and maximum bounding box sizes. If the size of the model is close to the maximum bounding box, then the printing orientation will be restricted.

Walls

Supported Wall Thickness Min

1.0 mm

Unsupported Wall Thickness Min

1.0 mm

A supported wall is connected at least on two sides of the wall, while an unsupported wall is connected only on one side of the wall. Walls that do not meet the minimum requirements may not survive printing and cleaning processes. Additionally, models may still be rejected based on the wall geometry of the model. Please consider the size of your model and reinforce the walls or add support structures as needed as minimum guidelines will not always be adequate for large models.

Wires

Supported Wires Min

0.8 mm

Unsupported Wires Min

0.9 mm

A wire is a circular, rectangular or even triangular feature that is thinner in its unconnected directions than its length. A supported wire is connected at least on two sides of the model, while an unsupported wire is connected on one side of the model. Wires that do not meet the minimum requirements may not survive printing and cleaning processes. Additionally, models may still be rejected based on the wire geometry of the model. Please consider the size of your model and reinforce the wires or add support structures as needed as minimum guidelines will not always be adequate for large models.

Details

Details Min Embossed

1 mm high & 1.5 wide Text should be embossed by at least 1.0 mm to stay visible after printing. Text should also be at least 1.5 mm thick in all areas.

Details Min Engraved

1 mm high & 1.5 wide

For text, the ratio between width and depth, should be 1:1 and sans-serif fonts are preferred for line weight consistency.

Escape Holes

Single Escape Hole Diameter (Min)

4 mm

Multiple Escape Hole Diameter (Min)

2 mm

Escape holes are necessary to empty the support material of a hollow model. Two escape holes at the opposite ends of the model is optimal for the support removal process. Please consider the size of your model and make the escape holes bigger or add more escape holes as needed as minimum guidelines will not always be adequate for large models.

A single escape hole at the end of a cavity will not allow material in the corners near the escape hole to fully escape. So we recommend multiple escape holes at both ends of the cavity.

Clearance

Min

0.2 mm offset on each wall is the recommended gap for enclosures

Clearance is the space between two individual parts in a model. If the space among the individual parts do not meet the minimum clearance, then parts can fuse together or can be difficult to clean. This is important for movable pieces like hinges, gears, etc.

Sprues

2 mm

Sprues are wires that keep two or more parts together. Parts should be connected with a minimum of two sprues each. Please consider the size of your sprues and increase them as needed as minimum guidelines will not always be adequate for large models. If the sprues are within the guidelines and are broken, but there is no damage to your model, we will still ship them as is.

Interlocking & Enclosed Parts

Interlocking
Yes

Enclosed
Yes

Parts in File

Max
Up to 250

Accuracy

Accuracy ± 0.004”, or ± 0.001” per inch, whichever is greater

For example: a product with dimensions of 50x50x100 mm can be 0.15 mm + 0.0015*100 mm = 0.3 mm bigger or smaller in any direction.

Other Materials

Nylon 12 powder Bed Fusion

FS3300PA

Application: Create complex parts and plastic models, Automobile gasoline pipe line, brake tube, Spare parts manufacturing or big parts joining with adhesives.

Nylon 12 Powder Bed Fusion

FS3400GF